Wind turbine ANTARIS 3.5 kW connected to the grid

Wind turbine ANTARIS 3.5 kW connected to the grid

€ 17.282,03

Inclusief belasting

Referentie: 0289

EAN13: 3170000004708

The high-performance Antaris 3.5Kw wind turbine is designed in Germany.

It's perfect for a home installation

Domestic wind turbine ANTARIS 3.5 kW

The Antaris wind turbine is specially adapted to sites inland. It is specially designed for network connection, charging batteries (24VDC / 48 VDC etc.) and powering heating systems. Because of its robust design, the Antaris wind turbine is also suitable for storm-prone locations.

The rotor blades are laminated by hand and benefit from a computer-designed aerodynamic profile, they are also balanced statically and dynamically. Each blade has an identification number and comes with its appropriate documentation. The highest importance has been to ensure the speed and simplicity of installation of this wind turbine.

Thanks to its robust and careful design, the Antaris wind turbine has excellent efficiency and is offered at a highly attractive price. It starts very quickly (starting already at a wind speed of 2.2 m/s) and operates silently (43 dB). This wind turbine can therefore be installed in residential areas.

The connection to the network requires the use of two inverters programmed specifically to operate with Antaris wind turbines as well as according to local wind conditions. In less windy areas, it is possible to connect the wind turbine to the grid via a single inverter. The inverters come with a declaration of compliance. The ENS (Electronic grid guard system) is integrated into the inverter.

Technical features

Generator

Permanent magnet rotor without brooms and gears. Doesn't require maintenance!
NdFeBo permanent magnets very powerful for great efficiency, resists up to 150oC
Phase
Separate lifter
Rotation in both directions
Tension 0-1000 VDC
Starts production at about 100 t/mn
Power: 6000 watts at 380 t/mn and 400V
Linear power curve
Weight: 31kg
Carter aluminum, cooling of the surface and the fastening base
Protection IP56

Rotor

Connection hubs with aluminum strap and overpressure plate
Stainless steel fitting screws and counter-nuts
3 Carbon rotor blades
Computer-designed aerodynamic profile
Noise reduction on the end of the blades
4m in diameter
Blade weight: 3.3 kg
Dynamically balanced
Anti-clockwise rotational sense
Rotation speed up to 300 t/min
GRP spinner cap
The colour of the rotor of your choice

Chassis

Weather-resistant HDPE Girouette
Support element: stainless steel square tube
All threaded fittings are made of stainless steel and equipped with nuts
Steel support for the generator, configured for plug-in in the azimut bearing frame, fully galvanized
Protected by a patented rotor-blade positioning system
Mast adapter with bridle connector (114.3 mm tube)

Storm protection

Switching the pale rotor to the "helicopter" position
Electronic control of turbines

Control cabinet

Control system with voltage monitor
Electronic control of turbines with regulator
Connector protections against polarity inversions
Controlling the phases of the alternator during the turbine mode
Emergency shutdown switch
Key switch re-initializer (removable)
2x 3 kW braking resistance

Inverter Smart wind 5kW

Three-phase power converter for small wind turbines

MODERN - FLEXIBLE - POWERFUL

Max. 20 kW wind turbine charge (SW-10)
Three-phase network coupling with 10 kW (SW-10)
Flexible and intelligent management of clean power, heating, battery and discharge charges through 4 separate CC energy outlets
Energy meter for power and heating
Reactive power control
Battery buffer interface - optional

Compact

Direct connection of the particle generator without additional equipment
Wide range of input voltage for particle generators
Compact case design with separate aperture connection area
Passive convection cooling on a wide range of performance
Integrated network/system protection (NA protection according to VDE AR-N 4105)

PROFITABLE - SURE

Built-in control features for a wind turbine Intelligent and finely tuned characteristic curve for optimal wind use
Characteristic curve freely selectable depending on voltage or speed
Many monitoring functions, such as wind speed or speed
Switch to stop the KWEA with other safety features

Communicative

Built-in graphics display
Built-in web server
Smart!wind Explorer PC's convenient use and setting interface

APPLICATION AREAS

Small wind turbines
Small hydroelectric plants
Mini-cogeneration

Characteristics

General data	SW-5.5
Size	656 x 472 x 234 mm
Weight	42 kg
Protective class	IP54
Cooling	Passive air/fan controlled according to demand
How it works in the temperature range	-25 degrees Celsius ... -40 degrees Fahrenheit - automatic decommissioning
Global efficiency	No more than 94%.
Clean consumption	18 W - Waiting
Clean consumption	83 W - Active offer
Entry generator side
Generator type	excited constantly / 3 phases
Generator-side lifter	B6
Entry voltage range (driver-driver)	60...500 VLL
Entry current (nominal value)	180 ... 500 VLL - for a total power of 5.5 kW
Entry power	600 VLL - maximum
Maximum value limited by load resistance	20 A - face value
Frequency of entry	40 A - max. 5 s
Monitoring generators	12 kW - face value
Monitoring generators	24 kW - max. 5 s
Exit sector side	0 Hz ... 150 Hz
Inverter sector side	Isolation control
Number of phases	Temperature control
Output power (nominal value)	Speed control
Exit tension
Inverter sector side	IGBT B6
Number of phases	3
Output power (nominal value)	5.5 kW
Exit tension	400 VLL - face value
	318 ... 460 VLL - eligible reach
Outfed current (nominal value)	0 ... 8 A
Exit frequency	0 Hz ... 150 Hz
Separation concept	without transformer - no galvanic insulation
Current distortion factor	3%
Power factor - cos	regulated to 1 - regulation according to VDE AR-N 4105
Resistance to short circuits	Current control
Network/system protection - ENS	VDE AR-N 4105